gas fireplaceservice.
← Back to the service guide

A clearer next step

Something not
quite right?

Start with what you’ve noticed. We’ll help you gather useful information and decide when to bring in a professional.

For gas fireplaces, inserts, stoves and gas log systems. Controls and service requirements vary by model.

Read this first

Gas odor or a CO alarm?
Get outside. Call for help.

Smell gas or suspect a leak?

Leave the building immediately. Do not try to light the fireplace, operate switches, use a phone inside, or investigate the leak. From a safe location outside, call 911 and your gas utility or propane supplier’s emergency number.

Carbon-monoxide alarm sounding?

Get everyone outside to fresh air immediately and call 911 from outside. Do not stay inside to find the source or silence the alarm. Do not re-enter until emergency responders say it is safe.

Do not wait for a service appointment or a reply to an online form in an emergency.

Choose what you’re noticing

What’s happening with
your fireplace?

These are starting points, not a diagnosis or confirmation that an appliance is safe to use. Only try basic checks when there is no gas odor, CO alarm or other safety concern. Always consult the manual.

Valor fireplace is beeping but not coming on

Common Valor Beep Meanings

Match the sound and when it happens to your specific Valor control system. The pairing signals below refer to Valor’s Comfort Control instructions; other systems may differ. Always consult the manual.

  • Series of quick/fast beeps when trying to light: Valor identifies about three seconds of rapid beeping as a low receiver-battery signal. For systems described in its battery guide, replace the four AA alkaline batteries in the receiver battery holder or, if equipped, beside the wall switch. These are separate from the handheld remote’s batteries. Valor battery guide.
  • One short beep followed by one long beep during reset/pairing: The receiver has reached the reset stage of the pairing procedure.
  • Two short beeps after the remote button is pressed during pairing: Confirms successful pairing. Two short beeps during normal operation can also signal the start of ignition; context matters.
  • One long beep during pairing: The pairing attempt failed or the wiring may be incorrect. This is not a diagnosis of a wiring fault. Valor Comfort Control instructions (PDF).

What you can do

If there is no gas odor, CO alarm or other safety concern, follow your model’s battery-replacement instructions. Turn the fireplace and pilot off as directed and let it cool before accessing the battery holder. Only use the homeowner-accessible battery compartment; do not disturb wiring or gas components.

Changing batteries does not require re-pairing on the Comfort Control system described above. Its initial pairing instructions are in the qualified-installer section—do not press Reset simply because the fireplace is beeping.

Your next step

If fresh batteries do not resolve the issue, or you cannot safely access the holder, leave the fireplace off and request service. Tell us the model, beep pattern and when the beeping occurs. Follow the emergency guidance above if you smell gas or hear a CO alarm.

Request service
I started my fireplace up this year and noticed a smell

Why the odor can happen

A temporary dusty or burn-off odor can occur when a direct-vent gas fireplace is first used after a long break, or when a new appliance is being cured. That does not mean every startup odor is normal. If you smell gas, suspect a leak or hear a CO alarm, follow the emergency guidance above immediately.

  • Seasonal dust: Household dust, pet dander and other airborne particles can settle on accessible exterior surfaces and warm components while the fireplace is idle. Heating these deposits can produce a temporary odor.
  • New-appliance curing: Factory paints, oils and other materials may give off an odor during the initial burn-in period. Follow your appliance’s instructions and your installer’s guidance; the procedure varies by model.

What you can do

  • Clear accessible dust: Turn the fireplace off as directed and let it cool completely. Clean only exterior surfaces and areas identified for homeowner cleaning in your manual. Do not remove sealed glass, disturb logs or reach into controls to investigate an odor.
  • Follow the correct burn-in procedure: For a new installation, use the manufacturer’s specified settings, run times and cooling periods. There is no single burn-in schedule for every fireplace. Have your technician handle internal glass cleaning if it is needed.
  • Ventilate when instructed: During an expected, manufacturer-described curing cycle, open windows as directed. Ventilation is not a substitute for responding to a suspected gas leak or CO alarm. Do not disable alarms.

When to stop and get help

  • Rotten-egg or gas odor: Treat it as a possible natural gas or propane leak. Leave immediately without operating switches or using a phone inside. From a safe location outside, call 911 and your gas utility or propane supplier’s emergency number.
  • Burning-plastic or electrical odor, or an odor that persists, worsens or repeatedly returns: Discontinue use and arrange professional evaluation. Do not keep running the fireplace to try to burn it away.
  • Unsure what you are smelling? Do not assume it is dust or curing. Stop using the appliance and get advice; if gas is suspected, follow the emergency steps above.

Your next step

Tell us whether this is a new installation or a seasonal startup, how long the odor lasted, and whether anything else changed. Do not restart the fireplace to reproduce a concerning smell. Always consult the manual.

Manufacturer resources: Valor fireplace support and first-use guidance · Valor cleaning and maintenance. Use instructions for your own make and model.

Request service
It won’t turn on

What to note

Note whether anything happens when you use the normal control: a display, a click, a spark, or no response. Do not keep trying to ignite it.

What you can do

If there are no safety concerns, check the remote’s batteries and operating mode using your manual. Some systems need electrical power; others operate differently. Do not open electrical compartments or adjust gas valves.

Your next step

If the usual homeowner controls do not resolve it, leave the fireplace off and request service. Tell us what you observed.

Request service
The pilot lights, but the burner doesn’t

What to note

Tell us whether the pilot remains on and whether the fireplace uses a remote, thermostat or wall switch. This symptom alone does not identify a failed part.

What you can do

Check the operating mode and temperature setting in your manual. Observe only through the installed glass; do not remove it to test the appliance.

Your next step

If the burner still does not operate as intended, stop ignition attempts and arrange service.

Request service
It starts, then shuts off

What to note

Note roughly how long it runs and any error code you have already seen. A shutdown can have several causes and needs proper evaluation.

What you can do

Check whether a timer or thermostat setting could explain the shutdown, following the manual. Do not bypass a safety control or repeatedly reset the system.

Your next step

If shutdowns are unexplained or recurring, leave it off until evaluated. Do not run it again just to time or film the fault.

Request service
The remote or wall switch isn’t working

What to note

Note whether the remote display works and whether the appliance responds to its normal controls.

What you can do

For an accessible handheld remote, replace batteries as directed by the manual and check its mode or lock setting. Follow only the manual’s homeowner instructions for pairing. Do not bridge wires, open electrical compartments or bypass switches.

Your next step

If that does not resolve the issue, request service. Include the remote model or a photo if readily available.

Request service
There’s soot, an unusual odor, or a changed flame

What to note

If you smell gas, suspect a leak or hear a CO alarm, follow the emergency guidance above immediately. Do not troubleshoot.

What you can do

For new soot, unexplained odors or a noticeable change in operation, discontinue use and arrange evaluation. A flame’s appearance alone cannot confirm safe operation. Do not rearrange logs or media or attempt burner adjustments.

Your next step

Describe what changed and when. Do not relight the fireplace to reproduce the concern or take a photo.

Request service
The glass is cracked, damaged or loose

What to note

Keep the fireplace off and keep people away from damaged glass.

What you can do

If you can safely follow your appliance’s manual, turn off the pilot and remove the batteries from handheld remote controls. If the manual provides a homeowner lockout procedure that you can complete without risk of injury, follow it to help prevent accidental use. Removing remote batteries alone may not disable the fireplace. Do not reach near damaged glass, dismantle the appliance or force any control. If you cannot safely complete the shutdown procedure, keep people away and contact a qualified technician. Do not operate the fireplace with damaged or improperly secured glass, remove the glass to run it, or substitute ordinary glass.

Your next step

Request service so the correct glass assembly, seals and attachment can be evaluated for your model.

Request service
I’ve moved into a home with a gas fireplace

What to note

If its condition and service history are unknown, arrange an evaluation before first use.

What you can do

Gather any manuals, service records and the make/model if readily accessible. Do not assume instructions for another fireplace apply to yours.

Your next step

Ask us to assess the installation and explain the controls, care needs and any concerns found.

Request service
It works, but I don’t know when it was serviced

What to note

Normal-looking flames are only one part of the picture. Your manual sets out the appliance’s maintenance requirements.

What you can do

Look for the last service report and your model’s recommended service interval. Always consult the manual.

Your next step

Request maintenance and tell us about any changes you have noticed, even if the fireplace still operates.

Request service

Make your visit more useful

Help us arrive
better prepared.

Gather what you can without taking anything apart. Missing information is okay—our team can help.

Professional help, explained

You don’t have to
diagnose it yourself.

Tell Doctor Flue what you’ve noticed. Our team will follow up about your request, appliance and location. Our NFI Gas certified technicians evaluate the fireplace, explain their findings and provide a same-day report with photos and detailed descriptions.

Request service

Continue to Doctor Flue’s contact form. A request is not a confirmed appointment.

Questions about routine service? 1-800-438-3583

Emergency guidance: Consumers Energy gas safety · U.S. Consumer Product Safety Commission: carbon monoxide